EPS裝飾線條是一種新型的外墻裝飾線，是由高阻燃B1級防火的聚苯板為主體，粘貼耐堿玻璃纖維網格布，加以特殊的界面砂粘結復合而成的裝飾建材產品。EPS裝飾線條采用電腦數控切割，制作快捷，品種型號多，如：門套、窗套、檐口線、腰線及亭柱等部位，使建筑物的外立面更加美觀。

EPS decorative line is a new type of exterior wall decorative line. It is an environmental protection and energy-saving high-quality decorative building material product made of high flame retardant B1 fireproof polystyrene board as the main body, pasted alkali resistant glass fiber grid cloth and bonded with special interface sand. EPS decorative lines are cut by computer numerical control, with fast production and many varieties and models, such as door cover, window cover, cornice line, waist line, pavilion column and other parts, so as to make the facade of the building more beautiful.

EPS線條除了裝飾功能強大之外，它還有哪些讓人喜愛的理由呢?

In addition to its powerful decorative function, what other reasons do people like EPS lines?

EPS裝飾線條自重輕，無需打模澆灌，采用特殊粘粘砂漿，輕松上墻，任意施工;省工、省時、省料、施工簡便、成本低。而且，它的了EPS雕塑等傳統外墻建筑裝飾構件在墻面安裝后會不可避免地出現的冷、熱橋現象等眾多難題，且不受溫度變化影響，耐寒，耐熱;不受潮濕及酸雨的影響。

EPS decorative line has light self weight, no need for formwork and pouring, and adopts special adhesive mortar to easily go to the wall and construct arbitrarily; Labor saving, time saving, material saving, simple construction and low cost. Moreover, it solves many problems, such as cold and hot bridge phenomenon, which will inevitably appear after the installation of EPS sculpture and other traditional exterior wall architectural decoration components on the wall, and is not affected by the temperature change. It is cold-resistant and heat-resistant; Not affected by humidity and acid rain.

EPS裝飾線條能防火又不會發出有毒物質，而且建筑師也能隨心所欲地設計造型，與外保溫墻體形成配合。利用特殊的粘結材料和方法，一個人就可以安裝施工，尤其較大體量構件，只需粘結安裝。裝飾線流暢、美觀，線形間無縫隙。由于兩個線條之間使用了縫隙修補材料，可使縫隙全部消失，在以后的使用中也不會出現裂縫。

EPS decorative lines can prevent fire without emitting toxic substances, and architects can design shapes at will to form a perfect cooperation with the external insulation wall. Using special bonding materials and methods, one person can install and construct, especially for large mass components, only bonding installation is required. The decorative line is smooth and beautiful, and there is no gap between the lines. Because the gap repair material is used between the two lines, all the gaps can disappear, and there will be no cracks in future use.

EPS裝飾線條的施工工藝：

Construction process of EPS decorative line:

1、待安裝線條部位其他施工程序已經完成并驗收合格;

1. Other construction procedures for lines to be installed have been completed and accepted;

2、根據施工圖紙，在要安裝線條的部位彈出定位線;

2. Pop up the positioning line at the position where the line is to be installed according to the construction drawing;

3、根據圖紙安裝尺寸切割線條，切割時要考慮拼接縫寬;

3. Cut the line according to the installation size of the drawing, and consider the splicing joint width during cutting;

4、線條粘貼時，網格布應當翻包，粘結劑使用聚合物粘結砂漿，采用薄層滿粘法進行粘貼，用力擠壓線條使砂漿從周邊溢出，線條之間縫寬不大于3mm，粘結縫應隨粘隨勾，灰縫飽滿，并保持線條表面的整潔;

4. When pasting the lines, the grid cloth shall be turned over, the adhesive shall be polymer bonded mortar, and the thin-layer full bonding method shall be adopted for pasting. The lines shall be squeezed to make the mortar overflow from the periphery. The joint width between the lines shall not be greater than 3mm. The bonding joint shall be hooked with adhesion, the mortar joint shall be full, and the surface of the lines shall be kept clean;

5、對于較大線條，安裝時要求設置支撐進行臨時固定。

5. For large lines, support shall be set for temporary fixation during installation.

EPS裝飾線條施工注意事項：

Precautions for EPS decorative line construction:

1、施工時環境溫度應不大于38℃，不低于5℃，低于此溫度時粘結砂漿必須采用抗凍配方。風力不大于5級;

1. During construction, the ambient temperature shall be no more than 38 ℃ and no less than 5 ℃. When the temperature is lower than this temperature, the bonding mortar must adopt the antifreeze formula. The wind force is not greater than level 5;

2、安裝、切割EPS構件前，墻面不需灑水濕潤，粉塵、污漬等影響粘結強度雜物應清理干凈;

2. Before installing and cutting EPS components, the wall does not need to be watered, and dust, stains and other sundries affecting the bonding strength shall be cleaned up;

3、拼裝時，拼裝縫應盡量留于整根EPS構件中間部位;

3. During assembly, the assembly joint shall be reserved in the middle of the whole EPS component as far as possible;

4、粘結EPS構件時，砂漿用水按加水量進行。但拼接時砂漿加水量應較用量在1～2%;

4. When bonding EPS components, water for mortar shall be added according to the recommended water amount. However, the amount of mortar added during splicing shall be 1 ~ 2% higher than the recommended amount;

5、剛粘結的EPS構件應注意保養，安裝好的EPS線條要用彩布遮蓋，防止雨水沖刷、防止人為損壞。

5. Attention shall be paid to the maintenance of freshly bonded EPS components, and the installed EPS lines shall be covered with colored cloth to prevent rainwater scouring and man-made damage.